Written by 3:32 am Headphone + Accessory Reviews

Audio-Technica Headphones and Fit

Why do some headphone designs fit better than others? Audio-Technica’s offerings are a case in point…



AR-at6.jpg

If you spend any time investigating headphones you’ll quickly
find the two phrases “house sound” and “comfort” being bandied about
frequently, especially on enthusiast sites such as Head-Fi.

The term “house sound” refers to the characteristic sound and
harmonic balance of a particular headphone manufacturer’s products. Some
companies, such as Grado, Stax, and Beyerdynamic, definitely have a particular
sonic character that runs through most of their offerings. Other companies,
such as V-Moda and Sony have many different varieties of sonic “flavors” from audiophile-pure to big bottom head-thumpers.

And then there’s “comfort.” And how well a pair of headphones
fit your head not only affects their wearability, but also their sound quality.
With some headphones moving their position even slightly can change their sonic
signature in profound ways. Two different listeners can come to widely
different opinions about the sound of a pair of earphones merely because of the
differences in fit between them.

Of all the brands of earphones I’ve tried, for me Audio-Technica
has the widest variety of fit – from perfect to awful. What’s most surprising
about this wide disparity of fit options is that they all use the same basic
design – a pair of large curved metal rods with a spring-loaded pair of wings
that rest lightly on your head.

AR-at1a.jpg

The first pair of Audio-Technica earphones that I reviewed were
the ones that required the most “field modification” to make them fit my head
properly – the limited edition ATH-W3000 ANV. When I first put them on the top
edge of the headphone left a ½ inch gap between the headphone and my head. The
only way to get a good seal required rather extensive reshaping of the metal
headband from its stock C-shape to a shape halfway between a U and a V. The
bending was not for the faint of heart or bicep.

The second pair of Audio-Technica headphones I acquired was the
ATH AD-900 open-air headphones. Once more I had to bend the metal rods. When I first put on the AD-900s they simply slid off my head because they did not
sit firmly on my ears. Only by increasing the side-pressure by bending the metal rod’s curve into a tighter diameter, could I achieve a decent fit. And when I did acquire
the right fit, the overall sound quality of the AD-900s improved markedly, with tighter imaging,
superior bass extension, and more open treble response.

AR-at2.jpg

My third pair of Audio-Technica headphones were the ATH A-900x
closed-cup earphones. Unlike the other two pairs, the A-900x’s metal rods
needed no adjustments for a proper fit, but after a couple of minutes of
head-time I needed to raise the earphones slightly, as they had slipped down
too low on my ears. The remedy was the “rubber-band mod” which involved putting
a heavy-duty rubber band between the two wings on the headband, which increases the wing’s down-pressure so they sit slightly higher on your ears.Now they fit perfectly.

The last pair of Audio-Technica’s in my headphone “library” are
the ATH A-700 closed-ear cans. Buy Dig had a refurbished pair at a price I couldn’t
resist. But unlike their more expensive siblings, the ATH A-900Xs, the ATH
A-700s are the only A-T headphones that fit me perfectly without a single
adjustment of modification.How amazing is that?

Now, if I didn’t realize, know enough, or was “brave” enough to
modify their headbands, I would have concluded that the A-700s were the “best” Audio-Technica
headphones because they were the only ones that really fit me properly, without
adjustments. But after making the necessary adjustments, the other A-T
headphones can out-perform the A-700s. But stock, right out of the box with no
changes, the A-700s were the only Audio-Technica headphones I could actually use, because they correctly.

AR-at4.jpg

So what can you, gentle reader, take away from this?

Simply, that you need to do what it takes to make sure your
headphones fit optimally before taking stock of their sonic performance. Also, don’t be afraid to experiment and try as many fit options as possible with any
set of headphones (or in-ear monitors) before settling on “the one” final set-up. I always push in and then pull
out a pair of headphones once I’ve had them in position for a minute or so, just to
see what additional or reduced pressure will do for their overall fit and the sound.

Don’t misunderstand me – I genuinely enjoy each of the four
Audio-Technica headphones currently in my headphone library. But to garner the optimum sonic performance from any headphone it must fit well. And with most
of the Audio-Technica headphones I’ve used, getting a good fit does require physical
adjustment to their headband shape. But, the final results have been well worth the
effort…

(Visited 323 times, 2 visits today)
Close